Please place Orders Online

Email Questions
support@softenerparts.com

Technical Support 7 days a week.




Softenerparts.com is a BBB Accredited Water Conditioning Equipment Store in Venice, FL
Knowledge Base:  

You are here: Knowledge Base : Valve
Page of 10
Trouble Shooting Guide for the Fleck 5600 and 5600 Econominder Valve
  PROBLEM   CAUSE   CORRECTION 1.  Softener fails to regenerate. A.   B. C. Electrical service to u
STUCK Valve Fleck 5600 Rebuild Guide
Rebuilding the Fleck 5600, Stuck Valve It is very common for the main and brine pistons of the Fleck 5600 to need replacement after 5 - 10 years of use. The valve will get stuck trying
Autotrol Valve Leaking to Drain after Replacing Valve Discs
Question: After installing new flapper valve disc set in my Autotrol Valve, I checked the function before powering up timer. The valves all seemed to work. I then turned the water flow back on and ha
Culligan Valve Replacement
QUESTION: I have a Culligan Medalist outdoor water softener Serial # 48151804J23 around 3 1/2 years old plagued with problems. I want to replace the entire mechanism from the tank up. My ques
Water Flowing to Salt Tank after replacing Brine Valve Piston Assembly Fleck part 60032
Hi , I just received a new repair kit # 56PSKIT and have installed it, however it now puts too much water into the brine tank, so much so the float in the brine tank rises and shuts it off. What have
MacClean McClean Mac Clean Mc Clean Valve
The MacClean valves and tank are proprietary in design after 2001 ( bought out by CUNO, which in turn was bought out by 3M ). See: http://www.aquapure.com/ or http://www.aquapurefilters.com/store/prod
Hard water when Autotrol Valve is working and using Salt properly - By Passing the RESIN?
Problem: ** If the Autotrol softener valve is truly operating correctly and you truly have NO Soft Water, then it would mean the water is NOT going through your RESIN. By pass points are: * # 4 valve
Valve Replacements - How To Remove and Replace Valve Head on Water Softener Tank
Water Softener Valve Replacements Fleck 5600 Econominder Autotrol Series 255 Logix 760 Replacing your old control valve head can ad
Technetic 1000, Plus, 1100i replacement Valve Recommendation
Customer Question: Hi I have an Technetic 1100 it needs to be replaced can you tell what one would be the best to replace it with. Thanks The Valve that is closest to your Technetics is the Autotro
Relieving Pressure Fleck 5600 Valve
Relieving the Pressure on your 5600 Valve and the Tank. Put valve on By Pass, or turn water off Manually put the valve in "backwash" to relief pressure HOW TO RELIEVE P
Brine Valve Replacement in Salt tank ( with Float Shut Off )
Which Brine Valve for the Salt Tank? We have several "valves" that fit in the brine tank that can be used ( all do similar function ). see: Brass 2300 Shut Off Valve and Plastic 231
Fleck 3600 Valve Obsolete but can be Replaced
Fleck 3600 Valve Replacement Since more of the Fleck 3600 and most parts are obsolete, see: Fleck 3600 Parts Search Summary Our best recommendation is to replace the complete valve wi
Which Valve Size - 3/4" or 1" Valve for Rotor Disc and Seal Kit?
Note there are Two Size Valves. And they are called 3/4" and 1", but BOTH have 1" piping connections on the REAR. So, the fact that you have 1" piping / fittings, has NOTHING to do with whether your
5600 - difference between metered, 12 day softener valve and Backwash ONLY
What is the difference between metered demand control and 12 day skipper wheel? * Metered.. Meter Demand Operation ** The Fleck 5600 version - 12 day works ( regenerates ) according to the "days" or
APK5 - 255 Upper Valve Module - Brine Suction / Brine Tank Overflow after replacing the Top part of the Valve
PROBLEM: When it goes through the cycle it doesn’t take the water from the brine tank and then it overflows when it refills, is there something I can do or is the module defective. This started a few
MacClean Valve Head MCA models Replacement
Customer Writes: I need to replace my valve head. It is a McClean MCA1501M model. I am attaching photos of the head. Can you please let me know what replacement is needed and how much it will cost. *
Autotrol 155 ( 1550-TC ) Valve Leaks - How to solve them
Customer writes: My Autotrol 1550-TC unit leaks water from the control valve body. Should this be rebuilt or replaced to solved the leaking? **** Leaks are easy to fix. Either the o-rings, or flapper
HANKSCRAFT H2O PRODUCTS and Replacement Valves
Hankscraft's Mission Our company mission is to "Deliver value through innovation, creativity and diversification". It is simple, yet it guides everything we do. Our history dates back to the
Autotrol 163 or 168 replacement Valve Recommendation is Performa 263 or 268
Autotrol 163 ( backwash only ) and 168 ( water softener ) Valves were last made in the year 2000. While there is no direct replacement, the Models 263 ( replace 163 ) and 268 ( replace 168 ) Performa
Backwash Only Valve Replacement Options
If replacing a Fleck 5600 or similar Backwash Only Valve, We recommend one of the following, Fleck 5600 in standard or "L" power head with 12 day timer, see: http://www.softenerparts.com/Valve_Fleck_5