Please place Orders Online

Email Questions
support@softenerparts.com

Technical Support 7 days a week.




Softenerparts.com is a BBB Accredited Water Conditioning Equipment Store in Venice, FL
Knowledge Base:  

You are here: Knowledge Base : 5600
Page of 4
Trouble Shooting Guide for the Fleck 5600 and 5600 Econominder Valve
  PROBLEM   CAUSE   CORRECTION 1.  Softener fails to regenerate. A.   B. C. Electrical service to u
STUCK Valve Fleck 5600 Rebuild Guide
Rebuilding the Fleck 5600, Stuck Valve It is very common for the main and brine pistons of the Fleck 5600 to need replacement after 5 - 10 years of use. The valve will get stuck trying
Fleck 5600 parts rebuild with or without replacing the Timer Motor
Customer Comment: Your parts rebuild kit should also contain one, 1/30th timer motor. When the piston gets stuck in the seals or is very hard to drive thru regeneration, the timer motor's internal
Fleck 5600 Still Getting Stuck After Replacing the Pistons and Seals Kit
CUSTOMER WRITES: I have purchased parts for my fleck 5600 system before and I am again having trouble. The timer still gets STUCK. I have rebuilt it ( new Pistons and Seals Kit ) twice and now am not
H2OW TO Softener = Fleck 5600 SE valve on 10 x 19 tank in cabinet
* Customer wrote in looking for replacement tank for HOW TO ( H2ow To ) softener: Andrew,The hole in the top is approx.2 3/4" across-the overall height is 18 3/4" tall - outer diameter is approx. 10"
Water Soft WSCB-32D is Autotrol 255 460i or Fleck 5600 SE
Water Soft WSCB-32D is Autotrol 255 460i or Fleck 5600 SE Just to confirm. Our softener is WaterSoft model WSCB-32D. I was told by CSI Control, who referred me to you, that the control valve is 255 46
5600 Piston Assembly Types - Softener - Filter - Low Water
Piston Assembly 60102-00, 60102-10, 60102-20 What is the Difference? Technically ( see page 8 and 16-19 in Fleck 5600 service manual ); The color of the Teflon coating of the piston may be Gree
5600 - Manual Regenerate - Cycle Times
To regenerate the Fleck 5600 valve used on softener, without working timer motor. The following steps are involved in regeneration: Time to leave in each cycle Regen - none, valve does nothi
Brine Suction problem with Fleck 5600 or similar Hankscraft Valve
If your Fleck 5600 ( or similar Hankscraft design ) Valve is not drawing ( sucking in ) the salt water from your brine tank, then here is a list of things to check and information about Brine Suction
Brine Refill problem with Fleck 5600
If your Fleck 5600 Valve is not refilling the water to your brine tank, then here is a list of things to check and information to review about Brine REFILL Failure. see: Brine Line Flow Control b
Relieving Pressure Fleck 5600 Valve
Relieving the Pressure on your 5600 Valve and the Tank. Put valve on By Pass, or turn water off Manually put the valve in "backwash" to relief pressure HOW TO RELIEVE P
5600 - difference between metered, 12 day softener valve and Backwash ONLY
What is the difference between metered demand control and 12 day skipper wheel? * Metered.. Meter Demand Operation ** The Fleck 5600 version - 12 day works ( regenerates ) according to the "days" or
Photos 5600SE, 5600SXT, 6600, and 6700 - Which Kit or Pistons for these Electronic Timers
The Electronic Fleck Valves ( 5600SE, SXT, 6600, 6700, etc ) use Special Valve Bodies and matching Special Main Piston Assemblies. And the 3456PSKIT will not work to rebuild the 5600SE valve ( or S
Fleck 5600 SE or SXT are NOT the same as Mechanical Versions of Fleck 5600
The Electronic Fleck Valves ( 5600SE, SXT, 6600, 6700, etc ) use Special Power Heads. I have a Fleck 5600SXT. Do all of the Fleck 5600 parts fit this model too? * NO. The
Fleck 5600 SE or SXT are NOT Recommended over Mechanical Fleck 5600
Why we do not recommend the Electronic Fleck Valves ( 5600SE, SXT, 6600, 6700, etc ). The SXT is electronic, and has many weaknesses... Circuit board ( replacement cost $ 150 ) Transformer (
Program Wheel replacement on Fleck 5600 Valve
1 ) Remove label on the front control knob. 2 ) Remove screw under label. 3 ) Pull front knob, and 24 hour wheel off and out of the way. 4 ) Remove label on old program wheel 5 ) Remove screw that
Fleck 5600 - Power Head replacement - Standard in place of "L" Bracket
Customer Asks / Writes: Hi, I have a fleck 5600 Econominder "L" Series. It broke recently and I need a new unit ( just the top head unit is broken not the entire unit ). I just wa
Fleck Piston 24507 - Fleck Model 5656 / 5665 UF are NOT the same as Mechanical Versions of Fleck 5600
Fleck Piston 24507 - Fleck Model 5656 / 5665 UF are NOT the same as Mechanical Versions of Fleck 5600 or SE, SXT versions We have only seen this version of the Main Piston in models sold in
Recommendation of Fleck 5600 Econominder and Hankscraft Equivalent water softener replacement valves - Which Brand is Best?
I'm trying to decide what brand / manufacturer of water softener system is best. Who do you recommend? We like any system that uses the Fleck 5600 Econominder Valve. And these are not sold as a
How does Hankscraft metered valve compare with the Fleck 5600 or the Hankscraft digital unit in terms of lasting durability
How does Hankscraft metered valve compare with the Fleck 5600 or the Hankscraft digital unit in terms of lasting durability The RESINS does all the "work", so all water softeners are 95% the same in