Knowledge Base:  
How do you put a softener out of service without damaging it?
Last Updated: 09/09/2010
* Simply "by pass" the water flow to the softener or shut water off. And unplug electric.
If it the tank is in an area that could Freeze, move Tank to area that Can't Freeze. Freezing
can damage the Resins, Tank, and / or Valve.

* When you are ready to use the softener again, besides turning the water back on, restoring
electric to control, and setting time of day, you will want to manually start a regeneration of the
 system to "freshen" up the water in the Tank, before using the water in the home.




Please Rate the Usefulness of this Article

Comments:
 

Related Articles
 > # 1 FAQ = High Water in Brine Tank - Problem -Softener does not remove the water from my salt tank or overflow
 > Aerator Use and Cleaning Q & A
 > Air Check - Ball seated or dropping early during the BRINE/SLOW RINSE -Autotrol 155 or 255 Series
 > Air Check inside Brine Tank can becomes Stuck or Water Logged
 > Air in water lines after Softener Regenerates
 > AIR INJECTION OXIDIZING FILTER SYSTEM = AIO
 > Average Salt Amount Needed and Normal Water Level In Brine Tank
 > Basic Installation Guide for New Water Softener
 > Brine Tank Assembly - Questions, Answers, Video Link
 > Brine Valve Replacement in Salt tank ( with Float Shut Off )
 > ChemTech and Pulsafeeder chlorine solution pumps
 > Choosing a Resin - What is the Difference
 > Choosing a Softener System - Which Brand is Best?
 > Common Water Problems
 > Dishwasher Glassware Etching Cause Explained
 > Do I need an Iron Filter?
 > ECO - Friendly Alternative to SALT Softeners
 > Fittings Measurements Different Then Expected ( 1/4 and 3/8 fittings )
 > Frequency of Regeneration - How Often Should Softener Recharge?
 > High Water in Brine Tank - Problems and Solutions
 > How a water softener actually works and why does it feel slimy
 > How and Why to use Acid Neutralizing Media Calcite and Corosex ( Magnesium Oxide )
 > How do you determine if you actually need a softener?
 > How does Hankscraft metered valve compare with the Fleck 5600 or the Hankscraft digital unit in terms of lasting durability
 > How Long Until Water Feels Soft Again After Repair
 > Hydrogen Sulfide levels affected by amount of water used and the ground water table
 > I have a Water Softener, but I still have odor in my water. Why is that?
 > Iron Staining and my Water Softener seems to be working okay, Why is that?
 > Irrigation - Iron Removal options
 > Links to Other Websites
 > Looking for someone to Service My Water Softner ( Softener ) in my area.
 > MediaGuard filter on Distributor Tube can cause pressure loss
 > Motor Identification - How to determine Type and Part Number
 > No Pressure Unless the Softener is By Passed
 > No Salt Systems for Water Softening
 > Odor - Sulfur (Hydrogen Sulfide) in your water
 > Orange Sand Coming Into House
 > Potassium Chloride - Substitute for Salt ( Sodium Chloride )
 > Pressure Drop or Flow Rate reductions through a Water Softener / Filter System - Things to Consider
 > Pump Pressure Low or Cycles OFF and ON ( Well Water )
 > Recommendation of Fleck 5600 Econominder and Hankscraft Equivalent water softener replacement valves - Which Brand is Best?
 > Salt Usage In Water Softening
 > Salty Water Taste - New Valve Installation
 > Salty Water Taste in the Morning
 > Sediment filter ahead of the softener - When, Why, and Which one.
 > Sodium in the Water Softening
 > Sodium Levels in Water when Softened
 > Stains in Laundry - several possible causes
 > Stinky - Rotten Egg - Odor
 > UV for Water Purification - Does it Work?
 > What Brine ( Salt ) Setting Amount to Use?
 > Which is better or cheaper... Powdered Resin Cleaners or Res-Up Liquid?
 > Why Gravel is Not Needed in Residential Size Water Softener
 > Will a Water Softener make my water safe to drink?
 > Will a Water Softener remove the iron from my water?