Knowledge Base:  
Brine Refill Problem - No water in salt tank - Autotrol
Last Updated: 08/23/2018
Does the tank float have to touch the bottom of the tank to signal the autotrol to put water into the brine tank

* No.

or is it metered after the brine is injected into the softener ( I'm wondering if the float is in the wrong position)

* Float is to prevent OVERFLOWING, and does not control refill.

Refill is a "timed" cycle ( at the end of the regeneration process ),

AND

The "flow" rate of this timed refill is controlled by the Brine Control Dial.

This sometimes gets clogged and requires cleaning ( it unscrews from the Valve Body ). * Also, note:
There is one of your two flow control balls ( 4F ) sitting inside behind it ( refer to parts diagram of the valve body ).

And unscrewing is all there is to removing the control from the valve body.

And once removed you will see if there is any debris blocking the small white teeth openings ( they are what "regulate" the amount of water that get past during REFILL Cycle ).



Please Rate the Usefulness of this Article

Comments:
 

Related Articles
 > # 1 FAQ = High Water in Brine Tank - Problem -Softener does not remove the water from my salt tank or overflow
 > 3 ways the Backwash cycle could be "blocked" in an Autotrol system
 > 440 - 460 Output Gear Repeatedly Breaking After Replacement.
 > 440 or 440i - Which Timer Assembly Do I Have - How to Tell
 > 440 or 440i or 460TC - Cycles controlled by the Camshaft used
 > 440 Timer Rebuilding / Repair / fix Guide
 > 440 Tripper Arm Gear Repeatedly Breaking After Replacement.
 > 440 Upgrade to 760 metered demand Logix Timer - How?
 > 440i motor replacement guide
 > 440i Sticking in Backwash or Brine Refill
 > 440iHV, 460TC, 460i Timer Assembly WARRANTY Policy of Softenerparts.com
 > 460i Timer RESET if it is Regenerating EVERY NIGHT
 > 460TC or Logix 740 - Which Timer Replacement is Best?
 > 460TC Timer Off Set When Multiple Valves Used
 > 740 and 760 Logix Timer Programming Instructions
 > 940 and 960 Timer Obsolete - Replacement Options when used on 255 Valve
 > Air Check - Ball seated or dropping early during the BRINE/SLOW RINSE -Autotrol 155 or 255 Series
 > Air Check Autotrol Old 36F or Newer Style - How to Tell - How to Clean
 > APK5 - 255 Upper Valve Module - Brine Suction / Brine Tank Overflow after replacing the Top part of the Valve
 > Autotrol 155 ( 1550-TC ) Valve Leaks - How to solve them
 > Autotrol 155 or 255 - How to Tell Which You Have
 > Autotrol 155 or 255 - Injector Size / Color - Why BLUE is sometimes used on 8 inch tanks
 > Autotrol 155 or 255 High Water in Brine Tank - Problem No Suction or Overflowing
 > Autotrol 155 with 440 Upgrade to 740 Day timer or 760 metered demand Logix Timer - How?
 > Autotrol 163 or 168 Rebuild Kits
 > Autotrol 163 or 168 replacement Valve Recommendation is Performa 263 or 268
 > Autotrol Date Codes - Serial Numbers
 > Autotrol Valve Flow Rate Problem - Either Resin in Tank or Valve Discs not Opening Enough
 > Autotrol Valve Leaking to Drain after Replacing Valve Discs
 > Backwash Plug and Injector Cap Removal Tool
 > Backwash Plug Number - Autotrol How can I tell what number of backwash plug I need?
 > Brine Refill after Autotrol 155 or 255 Repair - Purge Air from the Valve head, Brine line & Air Check
 > By Pass - Autotrol Old Style - How to Use
 > By Pass - Autotrol Old Style - Leaking When Connected to New Autotrol Valve
 > Calender Over Ride setting for 760 and 762 Logix Timer Programming
 > Can an Autotrol 255 valve be converted from softener use to filter ( carbon ) use?
 > Err 3 on 740,742,760, or 762 Logix Timer
 > Fittings Measurements Different Then Expected ( 1/4 and 3/8 fittings )
 > Freeze Damage to Air Check Body Autotrol 255
 > Gears, Housing, Motor Inside the 460i and 460TC timers - What is the difference?
 > Hard water when Autotrol Valve is working and using Salt properly - By Passing the RESIN?
 > How To Repair A Logix Controller - Replacing Back Up Capacitor on the Board
 > Model 172 and 180 are Obsolete - Commercial Autotrol Valves and Parts
 > Model 360, 363 and 368 Autotrol Valves and Parts
 > NovRam, 460i and 460TC timers - What is the difference?
 > Performa Valves Keep Breaking 440i Timers - Solution is...
 > Screen shows 1.1 on 740,742,760, or 762 Logix Timer - Button Test Mode
 > Setting Time of Day with the Autotrol 440 Tripper Arm Gear 99F
 > Technetic - Series 1010 Bypass Valve
 > Technetic 1000, Plus, 1100i replacement Valve Recommendation
 > Top Distributor Modifications - MD1203 used with Performa 263 and 268
 > Turbulator - Why Would Someone Use This Over A Standard Bottom Distributor Basket / Riser Pipe?
 > Water Soft WSCB-32D water softener = Autotrol Valve Links