When two valves are controlled by the 460TC timers, and you need them to run on different nights,
To "off set" the digital timer, you can leave one unplugged for 1 day.
460TC is a replacement for 440 timers, and is a little "simpler" to program.
Have them SET to the same frequency ( Days... every 3rd is default ).
By leaving one unplugged and started up one day later ( plug in and set time ), that will make sure they are running of different nights.
Most dealers would have them go the same night, and keep the Rust filter 2 hours fast ( starting at 12 midnight ) and the Softener at standard time ( starting at 2 a.m. each night ).
Either way will keep them from running at the same time.
It has improved drive motor, electronic timer, and only 3 drive gears ( old 440 had 8 and 4 that loved to break ).
And since we have been asked, let me say, once programmed and running,
There is no way to tell when the next regeneration will be ( what night ), or when the last regeneration occurred by looking at the timer.
> # 1 FAQ = High Water in Brine Tank - Problem -Softener does not remove the water from my salt tank or overflow
> 3 ways the Backwash cycle could be "blocked" in an Autotrol system
> 440 - 460 Output Gear Repeatedly Breaking After Replacement.
> 440 or 440i - Which Timer Assembly Do I Have - How to Tell
> 440 or 440i or 460TC - Cycles controlled by the Camshaft used
> 440 Timer Rebuilding / Repair / fix Guide
> 440 Tripper Arm Gear Repeatedly Breaking After Replacement.
> 440 Upgrade to 760 metered demand Logix Timer - How?
> 440i motor replacement guide
> 440i Sticking in Backwash or Brine Refill
> 440iHV, 460TC, 460i Timer Assembly WARRANTY Policy of Softenerparts.com
> 460i Timer RESET if it is Regenerating EVERY NIGHT
> 460TC or Logix 740 - Which Timer Replacement is Best?
> 740 and 760 Logix Timer Programming Instructions
> 940 and 960 Timer Obsolete - Replacement Options when used on 255 Valve
> Air Check - Ball seated or dropping early during the BRINE/SLOW RINSE -Autotrol 155 or 255 Series
> Air Check Autotrol Old 36F or Newer Style - How to Tell - How to Clean
> APK5 - 255 Upper Valve Module - Brine Suction / Brine Tank Overflow after replacing the Top part of the Valve
> Autotrol 155 ( 1550-TC ) Valve Leaks - How to solve them
> Autotrol 155 or 255 - How to Tell Which You Have
> Autotrol 155 or 255 - Injector Size / Color - Why BLUE is sometimes used on 8 inch tanks
> Autotrol 155 or 255 High Water in Brine Tank - Problem No Suction or Overflowing
> Autotrol 155 with 440 Upgrade to 740 Day timer or 760 metered demand Logix Timer - How?
> Autotrol 163 or 168 Rebuild Kits
> Autotrol 163 or 168 replacement Valve Recommendation is Performa 263 or 268
> Autotrol Date Codes - Serial Numbers
> Autotrol Valve Flow Rate Problem - Either Resin in Tank or Valve Discs not Opening Enough
> Autotrol Valve Leaking to Drain after Replacing Valve Discs
> Backwash Plug and Injector Cap Removal Tool
> Backwash Plug Number - Autotrol
How can I tell what number of backwash plug I need?
> Brine Refill after Autotrol 155 or 255 Repair - Purge Air from the Valve head, Brine line & Air Check
> Brine Refill Problem - No water in salt tank - Autotrol
> By Pass - Autotrol Old Style - How to Use
> By Pass - Autotrol Old Style - Leaking When Connected to New Autotrol Valve
> Calender Over Ride setting for 760 and 762 Logix Timer Programming
> Can an Autotrol 255 valve be converted from softener use to filter ( carbon ) use?
> Err 3 on 740,742,760, or 762 Logix Timer
> Fittings Measurements Different Then Expected ( 1/4 and 3/8 fittings )
> Freeze Damage to Air Check Body Autotrol 255
> Gears, Housing, Motor Inside the 460i and 460TC timers - What is the difference?
> Hard water when Autotrol Valve is working and using Salt properly - By Passing the RESIN?
> How To Repair A Logix Controller - Replacing Back Up Capacitor on the Board
> Model 172 and 180 are Obsolete - Commercial Autotrol Valves and Parts
> Model 360, 363 and 368 Autotrol Valves and Parts
> NovRam, 460i and 460TC timers - What is the difference?
> Performa Valves Keep Breaking 440i Timers - Solution is...
> Screen shows 1.1 on 740,742,760, or 762 Logix Timer - Button Test Mode
> Setting Time of Day with the Autotrol 440 Tripper Arm Gear 99F
> Technetic - Series 1010 Bypass Valve
> Technetic 1000, Plus, 1100i replacement Valve Recommendation
> Top Distributor Modifications - MD1203 used with Performa 263 and 268
> Turbulator - Why Would Someone Use This Over A Standard Bottom Distributor Basket / Riser Pipe?
> Water Soft WSCB-32D water softener = Autotrol Valve Links