Knowledge Base:  
Relieving Pressure Fleck 5600 Valve
Last Updated: 01/16/2019

Relieving the Pressure on your 5600 Valve and the Tank.

  1. Put valve on By Pass, or turn water off

  2. Manually put the valve in "backwash" to relief pressure

  3. HOW TO RELIEVE PRESSURE VIDEO






Please Rate the Usefulness of this Article

Comments:
 

Related Articles
 > # 1 FAQ = High Water in Brine Tank - Problem -Softener does not remove the water from my salt tank or overflow
 > 5600 - difference between metered, 12 day softener valve and Backwash ONLY
 > 5600 - Manual Regenerate - Cycle Times
 > 5600 Piston Assembly Types - Softener - Filter - Low Water
 > Air Check - Ball seated or dropping early during the BRINE/SLOW RINSE -Autotrol 155 or 255 Series
 > Alternate Drain Fitting that comes with every Hankscraft Valve
 > Autotrol 155 or 255 High Water in Brine Tank - Problem No Suction or Overflowing
 > Average Salt Amount Needed and Normal Water Level In Brine Tank
 > Backwash Only Valve Replacement Options
 > BLFC button question 0.25 versus 0.50 gpm with Fleck
 > Brine Cam Gear Sheared and Broken Off Plastic Housing Inside
 > Brine Failure on ONE Tank Only - 9000 / 9100 Twin Alternating Valve
 > Brine Refill problem with Fleck 5600
 > Brine Suction problem or High Water in Salt tank with Clack WS1 Valve
 > Brine Suction problem with Fleck 5600 or similar Hankscraft Valve
 > Cabinet Model Design - Pros and Cons
 > Clogged Injector in Iron Filter
 > Continually Cycling ( Regenerating ) Problem - Fleck 9000, 9100, or 9500 Valve
 > Distributor Failure in Bottom of Resin Tank
 > Fittings Measurements Different Then Expected ( 1/4 and 3/8 fittings )
 > Fleck 24 volt AC transformer - Which to Choose
 > Fleck 2500 leak to drain - Reasons why valve is still leaking after replacing the Seals & Spacers ( 60021 )
 > Fleck 2510 Valve to Tank Adapter Leak - O-rings to replace
 > Fleck 3200 timer - Brine Refill Rate Explained
 > Fleck 3200 timer problems - if "stalling" or not "advancing".
 > Fleck 3600 Valve Obsolete but can be Replaced
 > Fleck 5600 - Power Head replacement - Standard in place of "L" Bracket
 > Fleck 5600 Econominder - Replacement - Repair Options
 > Fleck 5600 parts rebuild with or without replacing the Timer Motor
 > Fleck 5600 Replacement Timer Motor - Life Expectancy
 > Fleck 5600 SE or SXT are NOT Recommended over Mechanical Fleck 5600
 > Fleck 5600 SE or SXT are NOT the same as Mechanical Versions of Fleck 5600
 > Fleck 5600 Still Getting Stuck After Replacing the Pistons and Seals Kit
 > Fleck Piston 24507 - Fleck Model 5656 / 5665 UF are NOT the same as Mechanical Versions of Fleck 5600
 > Fleck SE or SXT Error Codes
 > Fleck Valve - Greensand application - Purple Water After Regeneration
 > Fleck Valves - LEAKS out the DRAIN HOSE
 > Fleck Yoke Dimensions - Internal, External and Center To Center
 > HANKSCRAFT H2O PRODUCTS and Replacement Valves
 > High Water in Brine Tank - Problems and Solutions
 > How Long Until Water Feels Soft Again After Repair
 > How to Set Meter without the People or Hardness Labels on Fleck Econominder Valves
 > Iron Filter, Greensand, MGS, Birm and Issues including Clogged Injector
 > Low Pressure Through Softener On Chlorinated Water
 > Low Pressure Through Softener On Well Water
 > MediaGuard filter on Distributor Tube can cause pressure loss
 > Meter - Checking the Operation of the Fleck 3/4" Meter Cover
 > Meter - Cover Replaced, but Still not working..
 > Meter - Cover Replacement - How Long Should This Part Last?
 > Meter - Leak at Cable Connection Hole on the Fleck 3/4" Meter Cover
 > Meter Cable Length and Part Numbers for Mechanical Fleck Meter Covers / Models
 > Motor Identification - How to determine Type and Part Number
 > New Timer Motor 18743 kicks the unit into 'REGEN', but that's as far as it will go.
 > No Pressure Unless the Softener is By Passed
 > Orange Sand Coming Into House
 > Photos 5600SE, 5600SXT, 6600, and 6700 - Which Kit or Pistons for these Electronic Timers
 > Pressure Drop or Flow Rate reductions through a Water Softener / Filter System - Things to Consider
 > Program Wheel replacement on Fleck 5600 Valve
 > Pump Pressure Low or Cycles OFF and ON ( Well Water )
 > Refilling when it should Sucking Water out of Salt Tank ( Brine Rinse cycle ) Fleck Valve
 > Salt is Not Going Down. What could cause this problem?
 > Sears and GE Smartwater - Water Not Soft - Distributor Oring problem and solution
 > STUCK Valve Fleck 5600 Rebuild Guide
 > Switches Breaking Fleck 9000, 9100, or 9500 Valves
 > Tools Kit 60135-2510 for Service 1500, 2500, 2510 Seals & Spacers
 > Trouble Shooting Guide for the Fleck 5600 and 5600 Econominder Valve
 > Turbulator - Why Would Someone Use This Over A Standard Bottom Distributor Basket / Riser Pipe?
 > Valve Replacements - Fleck 8500 / Twinflo 100E with Fleck 9100 or a single valve / tank option
 > Water Flowing to Salt Tank after replacing Brine Valve Piston Assembly Fleck part 60032
 > Why Gravel is Not Needed in Residential Size Water Softener