|
|
|
|
|
|
|
|
|
|
|
1" Copper Adapter Kit - used with Erie Valves 541, 542 PN 541-252-2 or new # 75037
|
3/4" Copper Adapter Kit for Erie 541, 542 Valves 75036, 541-252-1
|
Main Diaphragm for Erie 541 and 542 Valves, NO LONGER AVAILABLE Separately. MUST BE ordered with new style Valve Stem.
|
|
|
|
|
|
|
|
|
|
|
|
|
Actuator ( 529-218 ) Erie 541 and 542 timers
|
3/4" female NPT Brass w/ Plastic Nuts & Gaskets, sold as set of two each. Old pn 541-282, and new pn 71962 Fits all Erie 541 and 542 models.
|
Backwash Subassembly ( flow adjuster with o-rings ) for variable flow control on Erie 541 and 542 Valves ( softener or filter valve application ).
|
|
|
|
|
|
|
|
|
|
|
|
|
Body Stem Assembly Erie part # 541-244 is no longer available in metal. Replacement is 72611 VALVE STEM & DIAPHRAGM REPAIR KIT
|
C -Clip for Erie Backwash Subassembly PN 19-19
|
Cap for Drain Erie Valves - 529-286 new pn 71897
|
|
|
|
|
|
|
|
|
|
|
|
|
Cover, Clear, Front Erie 541 and 542 529-234 new 71883 * Special Order - 2 week lead time *
|
Day Selector Wheel 12 Day 525-241-2 new 71818 used on Erie 541 and 542 timer controls. Part # 12A in diagram.
|
Diaphragm repair kit with Valve Stem
Body Stem Assembly Erie part # 541-244 is no longer available in metal. Replacement is Kit 72611, VALVE STEM in plastic & matching DIAPHRAGM with screw.
|
|
|
|
|
|
|
|
|
|
|
|
|
Drain Cartridge Repair Kit for Erie 541 and 542. If flow to drain will not stop, it is most likely this assembly that needs to be replaced.
|
Top Distributor for 1.05" distributor ( riser ) tubes. pn 287-166 or 75014 Commonly used on Erie 568, 2000, 2001, 2400 and all newer Erie Valves. Note many older Erie Valves could have either the 13/16" or an exact 1" distributor tube diameter, so please double check before ordering this part.
|
Gasket, Cross Over Port Oring - 529-244 Used in 541 and 542 type Erie Valve Body.
|
|
|
|
|
|
|
|
|
|
|
|
|
Gasket, rubber ( 541-213 new PN 71931 ) used for all Erie 541 and 542 Adapter Nuts.
|
GEAR, Time of Day ( 12 Day ) 529-232-1 new 71878 used on Erie 541 and 542 timer controls. Part # 5A in the diagram.
|
Injector Cap ( metal plate ) for Erie Valves with valve body 541 or 542.
|
|
|
|
|
|
|
|
|
|
|
|
|
Owners Service and Operation Manual for the Erie 542 Filter Valve
|
24 volt / 50 Hz International version ( 30-77-J / 71663 ) is SPECIAL ORDER
|
Timer Motor 120 Volt Erie 541 and 542 Valves. Old part number 529-A-241 or 30-77-F ( 71661 ) 120 volt / 60 Hz is always in stock, and ships immediately. Note: The drive gear has 9 teeth on it.
|
|
|
|
|
|
|
|
|
|
|
|
|
Oring for Cap ( 529-286 ) for Drain Erie Valves - 185-0221-1. New PN 71535 used on Erie 541 and 542 between the Drain Cap ( PE529286 ) and the Drain Plugger Kit ( PE529294 ).
|
185-028-12 Larger of the two orings found on the Seat Insert of the Erie 541 and 542 type valves. 185-024-1 is the small one also needed.
|
Smaller of the two orings from on the Seat Insert of the Erie 541 and 542 type valves. 185-028-12 is the large one also needed.
|
|
|
|
|
|
|
|
|
|
|
|
|
185-231-1 Used with the Erie 541 and 542 valve bodies and structural fiberglass tanks.
|
Thicker version used with older PARK tanks - O-ring between Valve and Tank, old PN PE186-136-N Used with the Erie 541 and 542 valve bodies and Park International fiberglass tanks.
|
Plug, Brine Line, Erie, 541-273, 541-277,70553
|
|
|
|
|
|
|
|
|
|
|
|
|
Ratchet Gear 525-254-2 w/ Ratchet (525260)
|
Retainer for Cap for Drain Erie Valves - 529-280 New PN 71894 used on Erie 541 and 542 under the Drain Cap ( PE529286 ).
|
Screw ( one ) for Injector Cap for Erie 541, 542 - PN 15-89, New PN 71511
|
|
|
|
|
|
|
|
|
|
|
|
|
Screw for Solenoid Erie 541, 542 - PN 15-91, New PN 71513
|
Seal Oring used on Back Cap of 541 and 542 models. 541-206
|
One gram of food grade silicone for use with o-rings, gaskets and seals. Enough to lubricate about a dozen or more o-rings and seals. These tubes come from one of the leading valve manufacturers.
|
|
|
|
|
|
|
|
|
|
|
|
|
Solenoid Coil - 24 Volt 413-134-24 PN 71702
|
542 backwash only filter valve. We have of NONE these valves remaining in stock. Erie has stopped making this model in the USA effective July 2016. We have several other Backwash Filter Valves that could be used as replacements ( Fleck 5600 and Hankscraft brands ). All would require some replumbing and additional By pass or Yoke for the plumbing connections, but would fit on same tanks used by Erie.
|
Complete 542 Egg Timer Back Wash Only Valve. Manual, 2-Hour Twist Timer, 542-030.
|
|