Home > Parts and Valves > Resin, Carbon,Tanks > Brine Tanks >

Brine Safety Float Pickup Tube BP1002

Brine Safety Float Pickup Tube
 
Alternative Views:


Your Price: $50.00

Availability: IN STOCK
Product Code: BP1002
Qty:

Description
 
Replaces old brass shut off float pick up assemblies.
Air check built into the bottom of the assembly.
Requires you have a Brine Well that is inside 3 1/2 " or 4" diameter.
We sell the 4" Brine Well listed below.
Sits in the Brine Well, and is held in place by your tubing connection and gravity.
Nothing needs to be screwed or bolted to the brine tank / brine well for this simple design.

NOTE: Shut Off is at the BOTTOM, which may be different than your older version ( which typically were at the top )
and the tubing connection is made at the "top" with included 3/8" Elbow ( AFTER cutting to your required height ).

Clack's 464 Brine Safety Float Pickup Tube comes 35" tall and can replace most old brass type brine shut off assemblies.
Comes with 3/8" Union Elbow ( jf506nsg ).
NOTE: This can be cut down to fit your salt tank.


How far off the bottom should the brine pickup tube go ?
(Touch the bottom if possible, or 1" or so off the bottom at most ).
*** Normally touching the bottom, but also okay if slightly above.

Also at what level should the Shut Off Float be placed on the Rod?
*** As high as it will go ( about 15 - 16 inches from bottom ).
And the Float ( on the Rod ) is SECURED in place at top and bottom of the float by the black rubber bushings ( grommets ) on the Float Rod.
This position is the 40% - 50% level of a residential size brine tank ( which are 30 - 36 inches tall ), but below any Overflow fitting you might have ( usually installed about the 75 - 80% height level of the brine tank ).

Failure to "secure" the float from the underside can result in the shut off "popping up" prematurely during the Brine Refill cycle.
The Float is held in place by the small black rubber grommets. The bottom one usually requires you slide it up into place.



Average Salt Amount Needed and Normal Water Level In Brine Tank

NOTE: Not Recommended for a Kinetico unit due to the constant pressure on the brine line of those systems.

Related Products...

Brine Safety Shut Off Valve 3/8" 2310 ( 60014 ) 3/8 x 3/8 inch elbow w/ steel grippers 506NSG Tank - Brine Complete 18 x 33 Round w/Safety Float Brine Well Cap - 4"
Your Price: $19.95

Add
Your Price: $4.50

Add
Your Price: $159.00

Add
Our Price: $1.25

Add
Safety Brine Valve Assembly, 2310 ( 60014 ) 3/8 x 3/8 inch plastic elbow with steel grippers 506NSG Tank - Brine Complete 18 x 33 Round w/Safety Float Brine Well Cap - 4"
Brine Well Tube 4 x 30 Slotted Brine Pick Up Tube with Air Check 60002 Overflow Fitting With Nut for Brine Tanks BWH1018 Potassium Float Assembly
Your Price: $19.95

Add
Your Price: $16.95

Add
Your Price: $2.95

Add
Your Price: $42.95

Add
Brine Well 4” x 30” Slotted Brine Pick Up Tube with Air Check  60002 Overflow Fitting With Nut for Brine Tanks Potassium Float Assembly, H7027-03
Brine Safety Float Assembly 30" Brine Well Clack 474 3/8" OD Black Tubing sold by Foot
Your Price: $45.00

Add
Price per Foot: $0.40
ENTER # of Feet You Need

Add
Brine Safety Float Assembly in Brine Well Clack 474 3/8" OD Black Tubing sold by Foot

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Parts and Valves > Resin, Carbon,Tanks > Brine Tanks
DIY Repair Guides > How to Replace Old Valve
Parts and Valves > Resin, Carbon,Tanks
DIY Repair Guides