# 1 FAQ = High Water in Brine Tank - Problem -Softener does not remove the water from my salt tank or overflow
1. Make sure all the fittings are tight. Also check the tubing going to the salt tank for small cracks. Any air leak will cause the valve to not draw the water out during the regeneration cycle.
|
# 1 Shipping Questions: When, How Long, From Where, What Methods
All Items are Brand New - 99.5% IN STOCK for SAME DAY Shipping We Do Not sell Used, Rebuilt or Refurbished Products.
Orders shipped same business day before 3 p.m. EST by U.S. Mail, or UPS Ground |
# 2 Pick Up at your Location ( store )?
We do not have a retail outlet.
It is recommended that you place your online order and let us mail it to you.
You can pick it up, but the order must still be placed ONLINE and PAID in advance of |
# 3 RETURN Policy and Procedure
Return Policy and Procedure
90 day money back - Or exchange.
Only a 15 % restocking fee + shipping and handling cost if return is
your mistake ( no restocking fee if the mistake is ours or |
# 4 EMAIL QUESTIONS - Better than a PHONE call.
For the fastest assisting with trouble shooting your water softener / filter problem, we strongly encourage you to email us. Please include your brand or valve type, and a description of the problem a |
440 or 440i - Manual Cycle Times if Motor Bad or No Power
How to Regenerate your Autotrol 440 or 440i when your timer assembly is broken.
Below is a list of the amount of time to leave the valve in each cycle ( stage ) of the Regeneration ( recharge / was |
440 or 440i - Which Timer Assembly Do I Have - How to Tell
How can I determine which timer assembly I have, 440 or 440i ?
* Look at the following photo, and diagrams.
440 on Left with face plate that is held on by 3 screws, Next to it is the 440i w |
440 Timer Rebuilding / Repair / fix Guide
An obvious problem that can occur is for the timer motor to fail. The motors turn at 1 rpm, so it is quite easy to tell if it is turning. A more common problem is for one or more of the drive gears t |
440 Upgrade to 760 metered demand Logix Timer - How?
There is NO Conversion "kit" for the metered Logix Valves.
You would have to have a different top plate ( for LOGIX timers, as opposed to the 440 timers ), and a few other parts ( brine control, in |
440i motor replacement guide
I bought an electric motor for my autotrol 440i. I can not figure out how to remove the motor. There is no screw in this one only a clip at the top and bottom. I can not turn it to remove it. Help!
|
440i Sticking in Backwash or Brine Refill
PROBLEM - Customer Writes,
If I manually regerate the dial and turn it to start it will start and then it seems like it gets stuck on backwash, I left it on there for over a hour and it did not adv |
440iHV Timer Assembly WARRANTY Policy of Softenerparts.com
Full warranty policy for the 440iHV timer assemblies.
90 days free exchange warranty We ship you a replacement (and pay postage to you) Then you return the defective one in same box (and you pay fo |
460i Timer RESET if it is Regenerating EVERY NIGHT
TOTAL 460 TIMER PROGRAM RESET
1. Record your Hardness and Capacity settings
2. Disconnect power
3. Jumper both pins 'A' and 'B' 4. Reconnect power for at least 10 seconds
5. Disc |
460TC or Logix 740 - Which Timer Replacement is Best?
Hello. I am helping my father purchase an Autotrol 255 Valve Module and I noticed that there are two option I can choose from. There is one that comes with the 460TC timer and one that comes with the |
5600 - difference between metered demand control and 12 day valve
What is the difference between metered demand control and 12 day skipper wheel?
* Metered..
Meter Demand Operation
** The Fleck 5600 version - 12 day works ( regenerates ) according to the " |
5600 - Manual Regenerate - Cycle Times
To regenerate the Fleck 5600 valve used on softener, without working timer motor.
The following steps are involved in regeneration: Time to leave in each cycle
Regen - none, valve does nothing |
5600 Piston Assembly Types - Softener - Filter - Low Water
Piston Assembly 60102-00, 60102-10, 60102-20 What is the Difference?
Technically ( see page 8 and 16-19 in Fleck 5600 service manual );
60102-00 ( softener ) piston Backwash = 10 minutes & |
740 and 760 Logix Timer Programming Instructions
Best place to start is the un-programmed state: Press and hold "set" ( square ) and "down" ( arrow ) buttons together for 5 seconds.
Then press and hold "set" ( square ) button for 5 seconds.
|
940 and 960 Timer Obsolete - Replacement Options when used on 255 Valve
QUESTION: I have a Autotrol 255/960 water softener and the 960 timer has stopped working I.e.it lights up all led's when initially powered on then goes completely dark.
Is there a replacement time |
Account Set Up to place Order - How do I?
Question: I would like to set up an account so I can place an order. How do I? Answer: No need to sent up an account in advance.
Your "account" with us is created the first time you place an online |
